Frequently asked questions on wall panelling
Product
Why use wall panelling?
The main reason is the creative possibilities to decorate any room, breaking the monotony of smooth painted walls.
Wall panelling allow a wide variety of technical solutions, for example: hide imperfections in the wall, increase the insulating capacity of the covered area, redistribute electrical fixtures, etc.
Wall panelling allow a wide variety of technical solutions, for example: hide imperfections in the wall, increase the insulating capacity of the covered area, redistribute electrical fixtures, etc.
What makes Zenku wall panelling unique and different to others?
We create high-quality panels for walls and ceilings that faithfully replicate noble and natural materials. Zenku has a wide range of designs and textures that allow you to get a natural finish with a significantly lower material and installation cost.
What is the difference between Zenku panels and natural wood panels?
The main difference is the cost. Zenku wall panelling cost between 50% and 70% less than wood. On the other hand, range of colours and tones is wider, offering much more decorative possibilities.
In addition, it is anti-allergenic, it does not accumulate mites, it offers greater resistance to fading caused by the sun and requires easier maintenance.
In addition, it is anti-allergenic, it does not accumulate mites, it offers greater resistance to fading caused by the sun and requires easier maintenance.
Installation
What is the first step in installing Zenku wall panelling?
The first step would be to check that the surface on which it will be installed is ready, dry and level. If it is not level, leveling paste must be applied with wedges on the battens.
Then proceed to place the battens.
Then proceed to place the battens.
How do I calculate the boxes needed?
On each box you can find the sqm you can cover by the material it contains. Then, divide the sqm you want to cover by the sqm contained in a box, and add a 10% more to cover waste generated by the installation.
What are battens? Is it difficult to place them?
Battens are low-cost slats on which the panels are fixed.
It is easy to install them. It is recommended to fix them to the wall using a drill. Drill the batten and the wall at the same time and then fix them with a screw that has the plug incorporated using a hammer. This requires just a few punches and is installed in few seconds.
It is easy to install them. It is recommended to fix them to the wall using a drill. Drill the batten and the wall at the same time and then fix them with a screw that has the plug incorporated using a hammer. This requires just a few punches and is installed in few seconds.
What direction should I give the panels when installing them?
The advantage of this product is that you can place the panels in any possible way. Vertical, horizontal, half height, diagonal…
An important point is to bear in mind that the batten must always be placed perpendicular to the panels. For example, in a vertical installation of the panels, battens must be installed horizontally, and vice versa.
An important point is to bear in mind that the batten must always be placed perpendicular to the panels. For example, in a vertical installation of the panels, battens must be installed horizontally, and vice versa.
How should I place the first panel? Where should I start?
It is advisable to start at the corner, placing the tongue facing the wall. Then, groove must be placed facing in the direction in which the installation will continue.
The first plank is the one that determines the good locking of the rest of the wall, so special care must be taken with its leveling. It must be fixed with a nail, then level it properly and finally you can fix the panel with the rest of nails.
The first plank is the one that determines the good locking of the rest of the wall, so special care must be taken with its leveling. It must be fixed with a nail, then level it properly and finally you can fix the panel with the rest of nails.
Do I need expansion gaps on the perimeter?
Yes, you must leave between 1 and 3 cm around the entire perimeter.
How do I fix the rest of the panels?
Once the first one is fixed, the rest of panels are tongue-and groove (tongue of a panel is placed inside the groove of the previous one). The groove of the panel must be fixed to the batten with staples, nails or clips. It is recommended to use clips as it allows expansion and, in case of disassembling, it does not damage the panels.
Can I change a panel placed in the middle of the wall if it is damaged?
Yes, you can do it. You must remove the finishing profile (if used) and then you must remove the panels from the end of the installation to the damaged panel. Once the panel has been replaced, you can reassemble the panels in the same way and place the finishing profile again.
How do I hide inner and outer joins?
For finishes it is advisable to use profiles of the same tone. It is easy to find them and install, and there is a wide range of colours for any design.
How do I install wall panelling around windows and doors? What about the switches?
In this case, battens must be placed around the entire contour of the window or door to fix the panels properly.
One of the advantages of the wall paneling is that it allows lighting to be included in the design of the space. As battens are used in the installation, a space between the panels and wall is created, allowing the redistribution of the electrical elements. Once the places where the light points will be placed have been decided, the holes to install the switches on the panels come be done using a drill and a saw.
One of the advantages of the wall paneling is that it allows lighting to be included in the design of the space. As battens are used in the installation, a space between the panels and wall is created, allowing the redistribution of the electrical elements. Once the places where the light points will be placed have been decided, the holes to install the switches on the panels come be done using a drill and a saw.
Maintenance
What kind of maintenance does Zenku wall panelling need?
Unlike wood, the wall panelling do not require special maintenance or additional varnish layers. Maintenance is just a normal cleaning routine.
Does it have to be cleaned with some special or specific product?
No, you do not need any special product. Zenku decorative panels must be cleaned dry with a damp cloth or vacuum cleaner, without applying chemical products.
